Home >> BLOG

A Maternity Pads Size Chart Describes the Underwear

A Maternity Pads Size Chart Describes the Underwear

Ask a maternity pad supplier for a size chart and you will receive a table with three columns: length, absorbency level, composition. None of the three describes the person who will wear the pad. The length describes a die, the level describes a test rig, the composition describes a declaration. That is not a defect in the document. It is a clue about what a maternity pad actually is: a dressing held in place by someone else's underwear.

The Maternity Pads Size Chart Describes the Underwear

A maternity pad is not held by the body. It is held by whatever the wearer is wearing, and in the first days after delivery that is usually a disposable mesh pant with a knitted crotch and no seam to register against. The pad has to be positioned by hand and kept in place by tension in the knit. Every column of a maternity pads size chart is a statement about that arrangement, not about a hip measurement.

This is why the same pad can be described as too short by one buyer and too long by another. Both are reading the length against a different garment, and neither garment appears in the table.

Hospital and retail channels differ again. A hospital knit is sized by waist range and laundered at a higher temperature, so it relaxes after the first cycles, and a pad that sat flat in a sample room can ride up after a day of use.

Length Without an Anchor Becomes Overhang

Usable coverage is not the number printed on the pack. It is the glued length plus a small margin, because the ends beyond the adhesive have nothing to hold them. In a loose knit those ends fold over rather than extend the covered area, and the fold is where a pad gives way first.

Ask for the glued length and its position, front and back. Two pads of identical length can differ by a wide margin in glued length, and the one with more glue at the back is usually the one that behaves when the wearer is lying down and flow moves along the body rather than down it.

A Size Range Is One Width on Several Lengths

A maternity pads size range is normally cut on one die width with several lengths, so the width is identical across the ladder and only the ends move. That is a manufacturing convenience, and it is also why a range of three items is often a shelf decision rather than a fit decision.

If the knit band at the crotch is narrow, extra length does not add coverage; it adds overhang at both ends. Measure the band first, then choose the shortest length whose glued section spans it. Two items in a range can also differ only in caliper, with the same length and width, which makes a shelf look fuller without giving the buyer a second fit.

ColumnWhat it describesWho fixes the value
LengthThe die and the adhesive patternThe converting line
Absorbency levelA class on a ladder run flat and unloadedThe laboratory method
CompositionLayer masses in descending orderThe declaration rules
CaliperThickness at a stated pressureThe gauge, not the pad

Absorbency Level Is a Statement About the Rig

An absorbency class is produced by a method, and the method runs flat, unloaded, with a defined volume delivered at a defined rate. The result is repeatable, and it is a true statement about the rig. It is not a statement about a person lying on the pad.

That is why a maternity pads absorbency level comparison between two suppliers can be meaningless even when both figures are honest. One laboratory may condition its samples before testing and another may not, and a conditioned sample holds a different figure from a dry one taken straight off the line.

What Compression Does to a Number Measured Flat

Under a body the cover film is pressed onto the topsheet and the core is squeezed. Liquid already taken in can be pushed back to the surface, and the figure that captures this is rewet under a stated load, not capacity on an open rig. The two are related but they are not interchangeable.

Flow also arrives differently. On a bench it is delivered as a steady dose; in use it arrives in gushes at an angle, and a pad built to take a slow dose in the centre can be slow to take a fast one near the end.

Do not read overnight protection as a number. It describes a use case, and the only way to compare two pads for that case is to compare rewet at the load the body actually applies.

Material Composition Is Declared by Mass, Not by Job

A maternity pads material composition list ranks layers by mass across the whole pad, which means the films, the release paper and the adhesive sit in the same column as the core. In a thin pad those layers can outrank the absorbent core, so two pads with nearly identical lists can carry quite different cores.

The reverse also happens. A change of pulp grade, or a shift in the ratio between pulp and superabsorbent, may leave the declared list untouched because the chemical names stay the same and only the proportions move.

Read the list as a legal document, then ask for a layer table that gives a caliper for each layer at one stated pressure.

Caliper Decides What the Wearer Actually Feels

Thickness is measured between two plates at a stated pressure, and the pressure is part of the answer. A pad gauged at a light pressure and the same pad gauged at a firm one give two different figures, and neither figure alone tells you how it behaves under a stretched knit.

Caliper is also the dimension the wearer reads as size. Two pads of equal length, one noticeably thicker, are described as small and large by the same person, because the eye reads volume and the hand reads compression.

For a buyer, caliper is the one column that can be verified on arrival with a gauge and a known load, which makes it the cheapest check in the whole document.

What a Purchase Spec Should Replace the Level With

Replace the level with four measurable rows: caliper at a stated pressure, glued length and position, rewet under a stated load, and backing film type with its moisture vapour transmission. Each row can be checked by a third party, and each one survives a change of supplier.

Order matters too. Length is set by the die, so it has to be agreed before artwork, because a change of length after printing means a new die and a new plate at the same time. Buyers who settle the artwork first tend to pay for the sequence later, in tooling and in weeks.

We have made pads in Shanwei since 1998 and ship from China, and the specification we quote against is one a buyer can measure rather than one a catalogue prints. For a consumer-facing version of the same argument, see the sanitary napkin range, how the pad is built on the line, the factory that cuts the die, private label programs, and the minimum order quantity for a first run.

Frequently Asked Questions

Does a maternity pads size chart use body measurements?

No. The columns describe a die, a test rig and a declaration order, so the table is read against the underwear that will hold the pad rather than against a hip or waist figure.

Why does pad length not equal usable coverage?

Because the ends beyond the adhesive have nothing to register against, and in a loose mesh pant they fold instead of lying flat, so covered area is set by the glued length.

Is a higher absorbency level always better for postpartum use?

Not always. A higher class usually means more core mass and more caliper, which changes how the pad sits under a stretched band, and the figure that matters in bed is rewet under load.

What should a buyer ask for instead of a composition list?

A layer table with a caliper for each layer and the pressure used to measure it, because the declaration only ranks masses and the films can outrank the core.

Can two suppliers send the same size chart and ship different pads?

Yes, and it is common, since length and level are classes while caliper, glued length and rewet are figures, and only the figures survive a change of die or film supplier.

Share LinkedIn X Facebook WhatsApp

Turn this note into a real production brief

Tell us the product type, target market, pack format and quantity you have in mind. We will reply with material options, tooling considerations and a sample timeline.

Request a quote WhatsApp
WhatsApp contact WeChat QR code

Nafei WeChat QR code