Period Pants for Heavy Flow and Overnight Wear
Heavy flow and overnight are two different briefs and should not share a specification. The fields to fix before sampling, the numbers behind them, and what we test.
Share target market, size range, pack count, artwork status and order quantity for quotation.
Introduction
Two briefs arrive in the same email more often than they should. A brand wants a pant for heavy flow, and it wants it to work overnight. Those are not the same requirement. One is about volume over a waking day. The other is about position, pressure and eight hours without a change. Different physics.
When the two get merged into one line on an order sheet, the sample comes back and fails in a way nobody can name. It holds the volume, yet the sheet is marked at 3 a.m. That is a geometry problem, not an absorbency problem. This page separates the two briefs and lists the fields we ask buyers to fix before sampling.
| Brief field | Heavy flow, daytime | Overnight |
|---|---|---|
| Stated capacity | 80 to 150 ml | 80 to 150 ml, used at lower fill |
| SAP weight per unit | 1.0 to 1.4 g | 1.0 to 1.4 g |
| Rise at the back | Standard | Extended, 15 to 25 mm higher |
| Leg cuff | Curved elastic, moderate stretch | Curved elastic, higher stretch |
| Backsheet | Breathable film | Breathable film, tested for 8 h wear |
| Size run | M to XL | M to XXL, with a longer body |
| Failure mode watched | Strike-through at the centre | Side and back leakage during turns |
Why capacity does not settle containment
A pant can hold 120 ml and still leak on a side sleeper. The fluid has to reach the core first. When the wearer turns onto her side, the pad surface tilts and gravity sends fluid to the lowest edge of the absorbent panel. If the panel ends before the cuff begins, that edge has nowhere to go.
We learned this on a Thai customer's overnight line in 2019. Her complaint list was specific: front leaks before midnight, back leaks after 4 a.m., almost nothing in between. The core was fine. The absorbent panel was 18 mm short at the back and the cuff sat below it. Widening the panel fixed a complaint that three SAP increases had not touched.
That is why the field that matters first is not capacity. It is the distance from the panel edge to the cuff seam, at the back and at the front. We mark it on the drawing in millimetres and check it on the first article. Millimetres, not adjectives.
The numbers worth fixing in writing
Capacity claims on a pack need a stated test method, or they are decoration. We quote a usable range, not a maximum, because a core tested to saturation is not a core a person can wear. State the method. A pant rated at 80 to 150 ml is being described across a size run and a fill level, and the test report should say which.
For context, a full menstrual cycle is usually given as 30 to 80 ml of fluid. A heavy day sits at the top of that band and a heavy cycle can exceed it. That number explains why a 150 ml pant exists and why most users never approach it on a normal day.
SAP weight per unit is the field we use internally to hit the band. Between 1.0 g and 1.4 g of superabsorbent in a pants format covers most heavy-flow briefs we quote. Above that, the core gets stiff and the fit changes, which trades a leak problem for a comfort complaint.
A practical rule from our sample room: if a buyer asks for more absorbency without naming a failure mode, ask for the failure mode first. Nine times out of ten the fix is not more SAP. Ask anyway.
Rise, size run and the side sleeper
Overnight briefs need a longer body and a higher back rise. On our line, the difference between a daytime pant and an overnight pant in the same size is 15 to 25 mm of back rise. It looks small on a drawing and it decides whether a wearer wakes up dry. Small number, large consequence.
Size run matters as much. A heavy-flow overnight brief sold only in M to XL will lose the upper end of the market, because the women who buy overnight protection skew larger than the daytime average. We quote M to XXL for overnight briefs and keep the same tooling across the ladder, so a brand can start with two sizes and add the rest without new tooling cost.
Elastic tension is the third variable and the easiest to get wrong. Too soft and the cuff gaps when she turns. Too tight and it marks the hip, which shows up as a one-star review rather than a return. We set it by wear trial, not by a number on a spec sheet, and we send the trial brief with the sample.
What we test before quoting a second order
Every overnight brief goes through three checks before we quote volume. The first is a static capacity test on the finished unit, recorded with the method name. The second is a cuff seal check on a body form at four positions: back, side, front, and seated. The third is a wear trial with 8 to 12 users over three nights, and it is the only one that finds the failures a form cannot.
The wear trial sheet asks one question per night: where did it leak, if it leaked. Answers come back as position, not as a score. Position data can be acted on. A score of seven out of ten cannot.
Sampling for an overnight brief runs 7 to 12 days from a locked brief, longer if the cuff geometry changes. We do not start a tooling change on a wear-trial comment alone. The comment has to point to a field, and the field has to be on the drawing.
The fields to send with an enquiry
A useful enquiry names six things: the market, the size run, the capacity band with a method, the rise preference, the packing format, and the failure mode the brand is trying to solve. With those six we can price and propose a sample without a call.
Brands often send a competitor's pack instead. That works as a reference for feel and thickness, not as a specification. We will match a reference where the construction allows it, and say so when it does not. A brief built on a reference alone tends to move three times before it locks.
If the brief is for a market with its own hygiene standard, name the standard and the version. We work to the current version in force, and we do not write a standard number into a pack claim without the test report behind it.
Where this brief links to the rest of the file
The absorbency field connects to the millilitre guide, which explains how capacity is measured and why a maximum number is the wrong thing to print. The size field connects to the size guide. The material field connects to the topsheet and backsheet options page.
For buyers building a range rather than a single SKU, the heavy-flow brief is usually the second SKU after a standard daytime pant. The overnight brief comes third, once the brand has data on its own returns. That order keeps tooling and artwork changes to a minimum.
Photos
Send a sampling brief for Period Pants for Heavy Flow and Overnight Wear
Tell Nafei your target market, size range, absorbency preference, packaging artwork status and estimated order plan. Our team can reply with sample discussion and quotation details.
- Target market and sales channel
- Size, pack count and material preference
- Private label artwork or packaging reference
- Sample review, quantity and delivery timeline
