Ask three liner suppliers for a size chart and you get three documents with no column in common. One lists S, M and L. One lists a single length. One lists four lengths and an absorbency level with no width anywhere. None of them is wrong. None of them can be compared, and none of them tells a buyer what the liner will do inside a pair of underwear.
A Liner Has No Hip Measurement to Grade
Garment sizing is built on circumference at the hip and the waist, and those figures move steadily as a size goes up. A liner does not sit there. It sits in the crotch panel of the underwear, a strip of fabric whose width barely changes between a small and an extra large garment, because the panel has to fit between the legs rather than around them.
That single fact is why S, M and L on a liner pack are a translation rather than a measurement. The brand has taken its garment ladder and mapped each step onto a liner it already buys, and two brands can use identical words for two different lengths while both remain honest.
A panty liners size chart that starts with S, M and L is therefore answering a question nobody in the category asked. What a buyer needs to know is which piece will sit against the body, and that is a physical dimension rather than a letter.
If you need the garment-side version of this reasoning, where circumference genuinely does the work, the pants sizing reference covers it in full.
What a Panty Liners Size Chart Actually Measures
A chart that is worth signing records physical facts about a finished piece. Three of them do the work at the buying stage: the cut length, the width at the widest point, and how far the backing film extends past the core at each end.
| Chart column | What it records | Where it misleads |
|---|---|---|
| Cut length | The die that will be ordered | The packed piece is shorter once it is compressed inside a wrapper |
| Width at widest point | The web the line has to run | On a contoured shape the widest point is not the middle |
| Backing extension | How much adhesive sits outside the core | Says nothing about tack, which is a glue and film pairing |
Anything beyond those columns is either a test result or a retail label, and the two should not share a table. A test result carries its conditions. A label carries a word.
Actually, the columns are the easy part. The difficulty is that a panty liners size chart is usually assembled by three different people at three different moments, and none of them is measuring the same piece.
Length Is a Die, Not a Trim
Length is fixed by the cutter roller, not by a setting on a screen. The roller carries a blade profile that repeats around its circumference, so every revolution produces a fixed number of pieces, and one turn delivers however many cut lengths fit on that circumference.
Change the length and you change the blade, the repeat and the pieces per turn together. This is why length is the most expensive column on the chart, and why a buyer who asks for four lengths is asking for four tools whether or not anyone says so out loud.
Narrow formats behave the same way. A teen liner is not a standard liner trimmed at the edge, it is a narrower web and a different die, and the folding geometry that turns a flat web into a wrapped piece has to be reset around it.
Most Sheets Call It Absorbency, but It Is a Core Build
Most sheets have a column they call panty liners absorbency level, and it is doing two jobs at once. One job is how much liquid the core takes up; the other is how dry the surface stays while it does. A tissue core with a light SAP load and a pulp-only core can carry the same label and behave nothing alike.
The mechanism is caliper. Adding SAP or pulp thickens the piece, and thickness changes the fold the wrapper former has to make, the film consumed per piece and the way a stack compresses into a bag. Absorbency is not a free column: it moves the wrapper.
That is the part buyers miss when they build a matrix. Three lengths against three absorbency builds is not nine labels. It is nine combinations, and the tooling behind them does not shrink because the cell in the spreadsheet is small.
Ultra Thin Is a Word Before It Is a Number
Most ultra thin panty liners are sold on an adjective, and the adjective has no fixed value. Thickness is read from a gauge under a stated pressure and after a stated settling time, so change either condition and the same piece reads differently.
Two factories can both describe a liner as ultra thin and ship pieces that feel different in the hand, and neither has lied. The word compares within one supplier's range, not across suppliers, which is exactly what a chart is supposed to fix.
If thickness belongs on the chart at all, it belongs there with its measuring pressure attached, the way a test report carries its conditions. A caliper figure with no pressure is a number somebody will dispute later, most often after the goods have landed.
Measure the Relaxed Piece, Not the Line Output
A liner comes off the line under tension and goes into a wrapper under compression, so the piece measured at the machine and the piece measured in the warehouse are not the same length. Any chart worth signing says where the measurement was taken and what happened to the piece before it was taken.
The protocol is short. Unwrap the piece, lay it flat without stretching it, let it settle, then measure. Do the same for width, and on a contoured shape state where the widest point was taken, because a shape that narrows at both ends has more than one candidate.
This is also why a physical reference sample beats a specification sheet during a transfer. Adhesive tack, cover hand-feel and wrapper tear cannot be read from a table, and a length on a sheet will not tell you whether the piece in your hand was measured before or after compression.
Building a Size Range on One Die
A panty liners size range does not have to mean several lengths. Retail shelves differentiate on pack count, pack format and cover material long before they differentiate on millimetres, and those three can move without touching the cutter, which is why the liner builds we supply are usually quoted around pack format first.
- Pack count first, because it changes the bag and the carton rather than the product.
- Wrapper format second, because a flow wrap and a bulk stack are different packing stations.
- Cover material third, because it changes feel and claim wording but not the die.
- Length last, because it is the only item on the list that needs a new tool.
Run the list in that order and six retail SKUs can sit on one die. Run it backwards and the same six need three dies, three first-article approvals and three sets of wrapper tooling, which is the difference between a launch and a project that never ships.
What the Chart Should Say When It Leaves the Factory
Once a figure is printed on a pack it stops being internal. A length printed on the front of a bag is a statement to a shopper in an aisle, and it will be checked against the piece inside by anyone with a reason to complain. We have cut liners and pads in Guangdong since 1998, and the charts that survive a transfer are the ones with conditions attached.
The safer arrangement is a chart that lives in the product file under a revision letter, and a pack that carries the brand's size word rather than a measurement. A word can be defended in a conversation. A printed millimetre cannot be adjusted after the print run.
Where the chart runs into cost is usually at the wrapper rather than the product. The packaging specification decides how many pieces the bag holds and how the carton is planned, and both of those move the minimum order before a single liner is made.
If you want a starting point, send the panty liners size chart you use today together with the sample it refers to. We will return both with the columns we can actually measure marked, note where the film and the die would have to change, and quote against that rather than against a letter. You can send the file here.
Frequently Asked Questions
Is there a standard liner size chart across brands?
No. Liner lengths are die dimensions set by each supplier's own tooling, and brands map their size words onto whatever length they buy, so two charts with the same S, M and L can describe pieces that are not interchangeable.
What should a liner size chart record first?
Start with the cut length, the width at the widest point and how far the backing extends past the core. Those three decide fit and adhesive behaviour. Everything else on the page is either a test result with conditions or a retail label with none.
Does a longer liner hold more liquid?
Not by itself. Length moves coverage, while capacity comes from the core build, so a longer piece with a pulp-only core can hold less than a shorter piece with a light SAP load. The wrapper changes with both, which is why the two columns are not independent.
How is liner thickness measured for a chart?
With a gauge under a stated pressure, after the piece has settled, on an unwrapped sample. Without the pressure stated, a thickness figure cannot be compared with another supplier's figure or even with your own earlier sample from the same factory.
Can we build a size range without new tooling?
Yes, if the range varies pack count, wrapper format and cover material rather than length. Add a second length only when the retail plan needs it, because a new length means a new cutter die, a new first-article approval and a new wrapper setup.
